Impact of Composition on Pore Throat Size in Mature Shales

Impact of Composition on Pore Throat Size in Mature Shales The impact of composition on pore throat size and permeability in mature shales: an example in Middle and Upper Devonian Horn River Group shale, northeastern British Columbia, Canada Tian Donga, Nicholas B. Harrisa, Korhan Ayrancia, Cory E. Twemlowb, Brent R. Nassichukb a Department of Earth and Atmospheric Sciences, University of Alberta, Edmonton, AB T6G 2E3, Canada, b Trican Geological Solutions Ltd., Calgary, AB T2E 2M1, Canada, Abstract Shale reservoirs of the Middle and Upper Devonian Horn River Group provide an opportunity to study the influence of rock composition on permeability and pore throat size distribution in mature formation. Sedimentological, geochemical and petrophysical analyses reveal relationships between rock composition, pore throat size and matrix permeability. In our sample set, measured matrix permeability ranges between 1.69 and 42.81 nanodarcies and increases with increasing porosity. Total organic carbon (TOC) content positively correlates to permeability and exerts a stronger control on permeability than inorganic composition. A positive correlation between silica content and permeability, and the abundant presence of interparticle pores between quartz crystals, suggest that quartz content may be another factor enhancing the permeability. Pore throat size distributions are strongly related to TOC content. In organic rich samples, the dominant pore throat size is less than 10 nm, whereas in organic lean samples, pore throat size distribution is dominantly greater than 20 nm. SEM images suggest that in organic rich samples, organic matter pores are the dominant pore type, whereas in quartz rich samples, the dominant type is interparticle pores between quartz grains. In clay rich and carbonate rich samples, the dominant pore type is intr aparticle pores, which are fewer and smaller in size. High permeability shales are associated with specific depositional facies. Massive and pyritic mudstones, rich in TOC and quartz, have relatively high permeability. Laminated mudstone, bioturbated mudstone and carbonate facies, which are relatively enriched in clay or carbonate, have relatively low permeability. Key words: Pore throat size; Permeability; shale composition; Horn River Group shale; Western Canada Sedimentary Basin 1. Introduction Typical shales or mudstones are sedimentary rocks with a dominant grain size less than 63 ÃŽÂ ¼m, serving as source rocks if organic matter is rich and as seals preventing hydrocarbon migration because of fine-grained nature (Schieber, 1998). Permeability is a fundamental property in conventional reservoirs that strongly influences hydrocarbon production rate. Permeability is presumably also important in shale reservoirs for long term flow rates, although initial production rates are also influenced by natural and artificial fracture systems (Jarvie et al., 2007; Rickman et al., 2008). Permeabilities in mudstones are typically several orders of magnitude lower than in coarser grained lithologies, such as siltstones and sandstones (Dewhurst et al., 1999; Nelson, 2009; Yang and Aplin, 2010). Published absolute permeabilities, measured on a variety of shales and by different analytical methods, typically fall in the nano-darcy range (Kwon et al., 2004). Because of the extremely low p ermeability, accurate measurements of permeability in shale samples are challenging (Sakhaee-Pour and Bryant, 2011; Tinni et al., 2012; Moghadam and Chalaturnyk, 2015). Steady-state flow techniques are impractical because it is difficult to achieve flow through shale plugs in a period of time short enough to permit analysis of large numbers of samples (Mallon and Swarbrick, 2008; Sakhaee-Pour and Bryant, 2011). Consequently, transient pulse decay methods, which require much less time, are generally employed to measure shale permeability on both plugs and crushed particles (Cui et al., 2009). One potential problem in using core plugs for pulse-decay measurements is that induced fractures may influence the measurements (Ghanizadeh et al., 2015); therefore, a crushed rock technique (the GRI method) may be a favorable method to measure the matrix permeability (Cui et al., 2009). On the other hand, where microfractures exist naturally in a shale, the GRI method might not be appropriate. In mudstones, permeability primarily depends on the abundance and size of pores and pore throats (Yang and Aplin, 1998; Dewhurst et al., 1999); under reservoir conditions, pore throats and consequently permeabilities may be substantial lower than measured under ambient conditions due to compression of pore throats. Permeability under in-situ conditions is difficult to measure, but it can be estimated from more easily determined petrophysical properties such as pore size and pore throat size distribution as well as surface area (Yang and Aplin, 1998). Mercury injection capillary pressure (MICP) measurements provide a qualitative understanding of permeability by giving useful information about the pore throat size and connectivity. MICP data suggest that pore throat size distributions in mudstones are influenced by porosity, grain size and clay content (Dewhurst et al., 1999; Yang and Aplin, 2007). Previously published data indicate that pore throat sizes in shales ranges from 5 nm to more than 100 nm (Nelson, 2009). Reported permeabilities in mudstones vary by ten orders of magnitude, primarily controlled by the presence of clay minerals, which decreases permeability by clogging mineral associated pores (Neuzil, 1994; Yang and Aplin, 1998, 2007, 2010; Dewhurst et al., 1998; Dewhurst et al., 1999). Permeabilities are also impacted by diagenetic processes such as destruction of porosity by mechanical compaction and cementation, and enhancement of pore throats by mineral dissolution (Pommer and Milliken, 2015). Most samples in these studies are either organic lean mudstones or low maturity, and the dominant pores exist between particles. Recently, high resolution scanning electron microscopy combined with ion milling techniques applied to mudstone samples has documented another important set of pores, i.e. those developed within organic matter (Loucks et al., 2009; Loucks et al., 2012; Nelson, 2009; Slatt and OBrien, 2011; Chalmers et al., 2012a; Curtis et al., 2012a; Curtis et al., 2012b; Dong and Harris, 2013; Dong et al., 2015; Mastalerz et al., 2013; Klaver et al., 2015; Tian et al., 2015). However, little work has been done on the control exerted by organic matter and other compositional variables on pore throat size distribution and permeability . Some studies have described pore features and factors controlling the matrix permeability in the Horn River Group shale (Ross and Bustin, 2009; Chalmers et al., 2012b), but none have been sufficiently detailed to determine the compositional factors influencing pore throat size distribution and permeability. In this study, we present a large dataset of permeability measurements on crushed samples and pore throat structure determined by MICP data By integrating geochemical data and petrophysical data for the Horn River Group shale, we investigate the potential effects of shale composition and organic matter on pore geometry, pore throat size distribution and permeability. We then link permeability to lithofacies, which can be used to predict spatial variation in permeability. 2. Geological setting The Horn River Basin, an area of nearly 12,000 km2, is situated in the deep northwest portion of the Western Canada Sedimentary Basin in northeastern British Columbia, Canada (Fig. 1) (Oldale and Munday, 1994). It is bounded to the south and east by carbonate barrier reefs (Presquile barrier) and to the west by the Bovie Fault, a Cretaceous structure associated with Laramide tectonism (Ross and Bustin, 2008). During the Middle and Late Devonian, the southern part was proximal to the paleo-shoreline and received more siliclastic input than the more distal northern part of the Horn River Basin (Fig. 1) (OConnell, 1994; Dong et al., 2016). The Horn River Group shale includes the Evie and Otter Park Members of Horn River Formation and the Muskwa Formation (Fig. 2), all deposited within a roughly 8 m.y. interval spanning the Givetian to early Frasnian Stages (~ 392 to 384 Ma) (Oldale and Munday, 1994). In the Horn River Basin, most of the Horn River Group shale is within the dry gas windo w with a vitrinite reflectance (Ro) ranging between 1.6 and 2.5% (Ross and Bustin, 2008, 2009; Rivard et al., 2014). The Evie Member is a dark grey, organic rich, variably calcareous mudstone that overlies the shallow marine carbonates of the Lower Keg River Formation (McPhail et al., 2008; Hulsy, 2011). The Evie Member is up to 75 meters thick near the Presquile barrier, thinning to less than 40 meters to the west (McPhail et al., 2008). The average TOC content for the Evie Member is 3.7 wt.% (Dong et al., 2015). The Otter Park Member is typically a grey, pyritic, argillaceous to calcareous mudstone. It is much thicker than the underlying Evie Member and the overlying Muskwa Formation, as much as 270 meters in the southeast Horn River Basin (McPhail et al., 2008). The Otter Park shale generally has lower organic content than either the Evie or the Muskwa, averaging 2.4 wt.% TOC (Dong et al., 2015). Portions of the Otter Park Member are rich in organic carbon with up to 7.09 wt.% TOC (Dong et al., 2015). The Otter Park shale varies geographically in composition, becoming argillaceous in distal part s of the basin to the north and west. The Muskwa shale is a gray to black siliceous, pyritic, organic-rich shale that overlies the Otter Park Member. The Muskwa Formation varies in thickness from 50 to 90 meters (Oldale and Munday, 1994). Organic carbon enrichment in the Muskwa Formation is generally higher than in the Otter Park Member but slightly lower than in the Evie Member, averaging 3.41wt.% TOC (Dong et al., 2015). The Muskwa Formation is overlain by the Fort Simpson Formation which is poor in organic matter. 3. Methodology We obtained core samples from four wells drilled in the Horn River Basin distributed from the northern distal part of the basin to southern proximal part: EOG Maxhamish D-012-L/094-O-15, Nexen Gote A-27-I/094-O-8, ConocoPhillips McAdam C-87-K/094-O-7 and Imperial Komie D-069-K/094-O-02 (Fig. 1). All samples were slabs cut from a 10 cm diameter core and were, on average, approximately 10 cm long and 6 cm wide. Splits were cut vertically along the sides of the core samples for geochemical analysis, permeability measurements, MICP analysis and SEM image analysis, so that the different analyses were performed on the same interval of rock. Before sampling, these four cores were stratigraphically logged in order to identify the sedimentological and ichnological characteristics and define lithofacies (see Dong et al., 2015, 2016 for methods on sedimentological analysis). Weatherford Laboratories analyzed total organic carbon (TOC) content using LECO combustion. Acme Analytical Laboratories determined the major element concentrations, including SiO2, Al2O3, Fe2O3, MgO, CaO, Na2O, K2O, TiO2, P2O5, MnO and Cr2O3 by using Inductively Coupled Plasma Mass Spectrometry (ICP-MS). Detailed information on analytical procedures for TOC and major oxides was provided in Dong et al. (2015). We selected ten samples (Table 1) for bulk mineralogical analysis and Based on the lithofacies classification, we selected five samples (Table 2) representing different lithofacies for QEMSCAN analysis, carried out by Whiting Petroleum Corporation, Denver. QEMSCAN is an automated SEM-based mineralogical analysis tool, and can be used for the quantitative determination of mineral abundance and identification of micro-texture (Ahmad and Haghighi, 2012). Permeability and porosity were measured on one hundred samples (Table 3) by Trican Well Service Ltd., Calgary, Alberta. Samples were crushed, sieved with a 10 mesh screen and dried in an oven at 105ËÅ ¡C to remove any existing fluids. Matrix permeability was measured on the crushed and sieved samples using the GRI method (Luffel et al., 1993). Helium pycnometry was used to measure the grain densities of each crushed sample. Ultra-high purity helium was used to maximize penetration of pore space and minimize potential reactions with the samples (Cui et al., 2009). Permeability was calculated at ambient conditions based on a method refined from ResTech (1996) and Luffel et al. (1993), and was not calibrated to insitu conditions. Pore throat size distributions were measured by mercury porosimeter on shale chips. We selected thirty-six samples (Table 4) from the four wells representing a wide range of TOC contents and mineralogical compositions to do the mercury injection analysis (Klaver et al., 2015). Mercury injection capillary pressure (MICP) analyses force mercury into pore throats and pores under increasing applied pressure. Pore throat diameters, not pore diameters, are then interpreted from the MICP measurements. The samples were dried in a vacuum oven over 12 hours and then intruded with mercury from 2 to 60000 psi using Micromeritics AutoPore IV 9500 V1.09 apparatus at the Department of Physics, University of Alberta. The minimal pore throat diameter can be measured by this instrument is 3 nm. Scanning electron microscopy enabled visualization of pores on samples polished with ion milling, which produces extremely smooth surfaces (Loucks et al., 2009). Eleven shale samples (Table 5) from core plugs were first mechanically polished and then further polished using ion milling (Fischione Model 1060 SEM Mill at the Department of Earth and Atmospheric Sciences, University of Alberta). Composition of the 11 samples is provided in Table 5. Ion milled samples were mounted to SEM stubs using carbon paste and coated with carbon to provide conductive surfaces. The prepared samples were imaged with two different field-emission SEMs. One was a JEOL 6301 F field-emission scanning electron microscope at the Scanning Electron Microscope Facility at the University of Alberta. We performed the FE-SEM analysis using an accelerating voltage of 5.0 kV and working distance range from 10-15 mm. The other was a Zeiss Sigma field-emission scanning electron microscope coupled with an EDX EBSD at t he nanoFAB facility, University of Alberta. The FE-SEM was performed using an accelerating voltage of 10.0 kV and working distance around 8.5 mm. Secondary electron (SE) images document the pore systems and topographic variation. Backscatter Electron Detector (BSE) and Oxford Instruments 150mm X-Max Energy Dispersive X-Ray Detector (EDX) provided the compositional and mineralogical variation. 4. Results 4.1 Lithofacies classification We identified five lithofacies based on thin section analysis and core observation from the four cores within Horn River Basin: massive mudstone, massive mudstone with abundant pyrite lenses and laminae (pyritic mudstone), laminated to heterolithic bedded mudstone (laminated mudstone), bioturbated mudstone, and carbonates. More detailed descriptions and photographs of the lithofacies are presented in Dong et al. (2015). Massive mudstone, lacking physical sedimentary structures and primarily comprising quartz (Figs. 3A and 4A), dominates the Muskwa Formation and the Evie Member (Figs. 5 and 6). Pyritic mudstone is characterized by pyrite-rich laminae and pyrite nodules (Figs. 3B and 4B), and dominates the Muskwa Formation in all four cores, and also dominates the Otter Park Member in the EOG Maxhamish core (Figs. 5 and 6). This lithofacies has less quartz but more clay than massive mudstone. Laminated mudstone is common in the Otter Park Member (Figs. 5 and 6) and consists of millimeter scale clay-rich mudstone laminae with quartz- and calcite-rich silt laminae (Figs. 3C and 4C). Bioturbated mudstone is characterized by moderate to intensely bioturbation and weak lamination (Figs. 3D and 4D) and primarily occurs in the lower part of the Otter Park Member (Figs. 5 and 6). Compared to the massive and pyritic mudstones, the laminated and bioturbated mudstones are relatively rich in clay (Figs. 4C and D) . The carbonate lithofacies, rich in calcite (Figs. 3E and 4E), is restricted to the lower part of the Evie Member (Figs. 5 and 6). 4.2 TOC content, major oxides concentration and mineralogy TOC content for all samples in our data set ranges from 0.04 to 8.25 wt.%, with a mean value of 3.09% (Dong et al., 2015). Lithofacies vary systematically in TOC content (Fig. 7A). Massive mudstone samples are richest in TOC, ranging from 0.82 to 8.25%, averaging 4.23 wt.%. Pyritic mudstone samples have TOC values ranging from 0.3 to 6.81 %, averaging 3.44 wt.%. Laminated mudstone samples have relatively low TOC, between 0.24 and 7.09 % (mean TOC = 2.02 wt.%). Bioturbated mudstone and carbonate mudstone samples have the lowest TOC values, between 0.04 and 3.05 % (mean TOC = 1.11 wt.%). TOC content is highest in Evie Member, moderate in Muskwa Formation and lowest in Otter Park Member (Dong et al., 2015). The oxides SiO2, Al2O3 and CaO represent the major components of quartz, clay and carbonate minerals, indicated by the strong correlation coefficient between major oxides and quantitative mineralogy from XRD analysis (Fig. 8). Thus concentrations of these oxides can be used as proxies for quartz, clay and carbonates. Oxide compositions differ greatly among lithofacies (Figs. 7B-D). The massive mudstone and pyritic mudstone lithofacies are relatively rich in SiO2, ranging from 9.9-80.1% and 12.3-89.4% with average values of 56.3 and 66.5%, respectively. The laminated mudstone and bioturbated mudstone lithofacies are richer in Al2O3, with concentrations of Al2O3 ranging from 2.0-17.0% and 9.1-19.7% with average values of 9.2 and 17.1%, respectively. The carbonate lithofacies is richest in CaO, ranging from 43.8-52.6% with an average of 47.6%. SiO2 concentration is highest in Muskwa Formation, Al2O3 concentration is highest in Otter Park Member, whereas CaO concentration is highest in E vie Member (Dong et al., 2016). Mineral components identified by X-Ray Diffraction (XRD) are presented in Table 1 and include quartz, K-feldspar, plagioclase, calcite, dolomite, pyrite and clay minerals (Dong et al., 2016). The clay fraction is dominated by illite and mixed-layer illite/smectite, plus a trace of chlorite in some samples. 4.3 Permeability Matrix permeability profiles from the EOG Maxhamish, Imperial Komie, Nexen Gote and ConocoPhillips McAdam cores are shown in Figs. 5 and 6. The average permeability for all samples is 15.6 nD, ranging from 1.69 to 42.81 nD (Table 3 and Fig. 9). Permeability is highest in the Evie Member (average permeability = 17.15 nD), moderate in Muskwa Formation (average permeability = 15.18 nD), and lowest in the Otter Park Member (average permeability = 14.44 nD). 4.4 Pore systems Porosity measured on core samples ranges from 0.62% to 12.04%, averaging 5.1% (Dong et al., 2015). Pores are categorized as micropores (pore diameter 50 nm) by the International Union of Pure and Applied Chemistry (Sing, 1985). Loucks et al. (2012) recognized three general types of pores in shales: organic matter pores, interparticle pores developed between grains and crystals, and intraparticle pores contained with a particle boundary. All three pore types were observed in our shale samples (Figs. 10, 11 and 12). In our Horn River Group shale samples, mesopores and macropores were observed in the high resolution SEM images (Figs. 10, 11 and 12). Micropores are smaller, below the limit of the SEM images resolution (Dong and Harris, 2013). Pores are common in organic matter and are predominately round or elliptical in cross-section with a wide size range from a few nanometers (Figs. 10B, D and E) to greater than 1 micron (Fig. 10C). Pore abundance within organic matter is strongly heterogeneous, with both non-porous solid organic matter and porous organic matter commonly observed (Figs. 10A and F). Even within the same patch of organic matter, we observed dense area and porous area (Fig. 10B). The size of organic matter pores is also highly variable; for example, mesopores dominate the pore system in sample IK4 (Fig. 10E), whereas macropores dominate sample M2(Figs. 10A and C). Interparticle pores are observed between quartz crystals, calcite crystals and other detrital particles, such as feldspar (Fig. 11). These pores display triangular and elongated shapes (Fig. 11), substantially different in morphology and size from organic matter-hosted pores which are typically ovoid and elliptical in shape. The pore size and morphology of interparticle pores depends on the surrounding minerals, geometry and arrangement of adjacent particles. Most interparticle pores are much larger than organic matter pores, typically greater than 100nm. Interparticle pores are also present between fine-grained phyllosilicate particles that occupy primary pores between carbonate particles (Fig. 12F), displaying smaller size. Intraparticle pores are found within particles or mineral grains, such as clay minerals, carbonate grains, pyrite framboids and apatite. They include primary pores preserved during burial and diagenetic processes and secondary pores generated by dissolution of feldspar and carbonate. Pore spaces within clay flocculates are common in clay rich samples (Fig. 12A). Pyrite framboids, aggregates of submicron pyrite crystals, are relatively common in Horn River Group shale and contain mesopores developed between the submicron pyrite crystals (Fig. 12B). Apatite also provides sites for porosity development (Fig. 12E). Numerous intraparticle pores are present within carbonate grains due to carbonate dissolution (Figs. 12D and E). All fractures observed in the Horn River Group shale are completely open and lack cement filling (Figs. 12C and D). In clay rich samples, the fractures are probably artificial shrinkage cracks produced as the clays dehydrated (Fig. 12C). In the carbonate rich samples (Fig. 12D), fractures surrounding calcite grains are narrower and shorter than fractures in clay rich samples and are interpreted to be natural. 4.5 Pore throat size distributions Porosity and pore size distributions, calculated from nitrogen adsorption analyses, were presented in Dong et al. (2015). These date show that the Horn River Group shale samples contain mixtures of macropores, mesopores and micropores. Pore throat size distributions are more critical than pore size distributions to permeability (Nelson, 2009). Sample preparation and applied injection pressure of up to 60000 psi may either cause artificial fractures in our samples or results in collapse of large pores (Yang and Aplin, 2007; Chalmers et al., 2012a). In this study, pore throats related to artificial fractures were removed from the distributions (Fig. 13). Samples in Figs. 13 are grouped by increasing TOC content. Pore throat diameter distributions are increasingly skewed towards smaller values with increasing TOC content. Samples with low TOC content (Figs. 13A, B and C) are characterized by asymmetric distributions with dominant pore throat radii greater than 20 nm. Pore throat diameters less than 10nm dominate in the organic rich samples (Figs. 13D, E and F). Median pore throat diameter is thus negatively correlated to TOC content (Fig. 14A), but no association with major inorganic components is evident (Figs. 14B, C and D). Mercury intrusion porosimetry also can be used to calculate effective porosity. Porosity calculated from mercury injection ranges from 0.6% to 2.9%, averaging 1.5%, which is much lower than total porosity measured by helium pycnometer. There is a positive correlation between TOC content and effective porosity, yielding a correlation coefficient of 0.44 (Fig. 15). 5. Discussion 5.1 Relationship between porosity and permeability Previous studies have shown that the relationship between porosity and permeability in mudstones is primarily controlled by the clay content (Yang and Aplin, 2007; 2010). At a given porosity, Dewhurst et al. (1998, 1999) found that clay poor mudstones are much more permeable than clay rich mudstones. The samples in the Dewhurst et al. (1998, 1999) studies were shallowly buried London clay, with a TOC content between 0.2 and 0.9 wt.%. The samples in the study of Yang and Aplin (2007) are core samples from North Sea and Gulf of Mexico, with a range of TOC from 0.1 to 2.4 wt.%. Samples in those studies are organic lean mudstones and no organic matter pores were reported in their studies. The loss of porosity and permeability is largely driven by the preferential collapse of large primary pores. The wide range of permeability (3 orders of magnitude) likely can be explained by the variation in grain size, which is in turn affected by the clay content (Dewhurst et al., 1998, 1999; Yang and Aplin, 2007). In our Horn River Group shale dataset, however, the relationship between porosity and permeability do not vary systematically with the concentration of Al2O3 (Fig. 9B), which is an approximation for clay content. Unlike the studies cited above, samples with high clay content does not show lower permeability at a given porosity than samples with low clay content. The primary reasons for the contrast between our results and those of Dewhurst et al. (1998, 1999) and Yang and Aplin (2007) are probably the high organic content and the high maturity of the Horn River samples and the definition of clay content. In their studies, clay content is defined as particles less than 2 ÃŽÂ ¼m regardless of mineralogy, whereas we defined the clay content as the abundance of clay minerals including smectite, illite, mixed layer of smectite+illite and chlorite. The samples in this study have a TOC content range of 0.04-8.25 wt.%, with a mean value of 3.09%, approximately 3 to 10 times higher than in the Dewhurst et al. (1998, 1999) and Yang and Aplin (2007) data sets. Ross and Bustin (2008, 2009) showed that Horn River Group shale is highly mature, with vitrinite reflectance from approximately 1.6 to 2.5% in contrast to the low maturities in Dewhurst et al. (1998, 1999) and Yang and Aplin (2007). Dong et al. (2015) reported that hydrogen index (HI) and oxygen index (OI) are very low in Horn River Group shale, indicative of dry gas window. Compared to economically successful shale gas plays in North American such as Barnett Shale (Jarvie et al., 2007) and Eagle Ford Shale (Pommer and Milliken, 2015), Horn River Group shale is more mature, although it is less mature than the gas-productive Silurian black shales in Sichuan Basin, southwestern China, which have an equivalent vitrinite reflectance (%Ro) range of 2.84 3.54 (Tian et al., 2013). We propose that the extensive development of organic matter pores in mature shales impacts the relationship between clay content and porosit y-permeability behavior. Porosity-permeability relationships are shown in Fig. 9. Our permeability data show a positive correlation with porosity, yielding a correlation coefficient of 0.72 for all the samples (Fig. 9A). Porosity is the strongest individual predictor of matrix permeability, stronger than any correlation between any compositional parameter and permeability. 5.2 Relationship between shale composition and pore throat size distribution TOC and median pore throat size calculated from mercury injection capillary pressure data (Fig. 14A) are negatively correlated, suggesting that smaller median pore throat size occurs in organic rich samples than in organic lean samples. The smaller pore throat size in organic carbon rich samples (predominantly less than 10 nm) is also evident in histograms of pore throat size distribution (Figs. 13D, E and F). This relationship is consistent with observations from scanning electron microscopy (Fig. 10), where most of the organic matter pores are less than 100 nm. Similar phenomenon have been observed in Devonian shales, Appalachian Basin, where pore throat size is much smaller in organic rich samples (averaging 8 nm) than in organic poor samples (averaging 22 nm) (Nelson, 2009). Bernard et al. (2012) suggest that in the Barnett Shale, organic pores formed not in kerogen, but rather in bitumen which derived from thermally degraded kerogen in the oil window and in pyrobitumen, which resulted from secondary cracking of bitumen in the gas window. In this study, bitumen, solid bitumen and pyrobitumen are defined as secondary organic matter, following terminology in Pommer and Milliken (2015). Although it is operationally challenging to distinguish bitumen or pyrobitumen from kerogen on SEM images, organic matter in the Horn River Group shale probably consists of mixtures of kerogen, bitumen and pyrobitumen (Fig. 10), as all the stratigraphic units are currently in the dry gas window. A certain fraction of the buried detrital and marine kerogen apparently has been converted to hydrocarbon and secondary organic matter, generating the numerous bubble-like pores (Fig. 10). Pommer and Milliken (2015) identified similar processes in the Eagle Ford Shale, where, over a range of thermal maturities from oil window to gas window, original primary mineral-associated pores are largely infilled by secondary organic matter, in which much smaller organic matter pores (median size 13.2 nm) later develop. Primary intergranular pores between rigid grains such as quartz, calcite were clogged by kerogen, bitumen and pyrobitumen, where small organic matter pores were generated because of the thermal conversion from kerogen to hydrocarbon (Figs. 10B and E). Clay content does not appear to be significantly related to pore throat size in the Horn River Group shale, in contrast to some previous studies (Yang and Aplin, 2007; 2010) (Fig. 14C). At deposition, pore throat size and connectivity is a function of the shape, size and packing pattern of the constituent clasts. Clay-sized particles damage matrix permeability by clogging pores and throats (Yang and Aplin, 2007, 2010). Large primary pores may have been present in the Horn River Group shale at low maturities and relatively shallow burial depths, but at its present-day high thermal maturity (gas window), primary pores have been largely lost due to compaction, suggested by the twisted clay flakes (Fig. 12A). In clay rich samples, only a minor amount of secondary organic matter pores are present (Fig. 12B). Any correlation between clay content and pore throat size that may have existed at low maturity was effectively erased by diagenesis. 5.3 Shale composition and permeability Organic matter pores, which generally are interpreted to be generated during burial and maturation (Jarvie et al., 2007; Zargari et al., 2015), have been well documented in organic rich shales such as the Barnett Shale, Woodford Shale, Marcellus Shale and the Kimmeridge Clay Formation (Loucks et al., 2009; Passey et al., 2010; Curtis et al., 2012a; Fishman et al., 2012

Age Segregation in Pakistan

Richard and Gill walker, looks into the social context of housing for aged ones. It covers the demographic material, facts about social framework of housing for older people. This includes a review of demographic information, evidence relating to the needs, perspectives and choices of the aged people with respect to this housing, along the problems of segregation and marginalization and their impact on their livings.Attitudes towards Old Age: A Study of the Self-Image of Aged is another article by Philip O. SiJuwade, which looks into the ifferent approaches , stereotypes, and age factors which regulates suitable behaviors for the older ones(social image). It states that, old ones have developed their self-image too, which depicts the way they think of themselves and the way ‘others' think of them. This article is based on primary research states that stereotypes have been built about the aged people of the society and they are not treated in the way they deserve to be.Residenti al satisfaction of the older adults in age-segregated facilities is an article by Sandra G. Reynolds and Julia O. Beamish hich looks into the housing satisfaction of old home people with liberated living services. Twenty one residents contributed as a focus group and results showed that these old people liked safe and secure atmosphere and value good design, friendly neighborhood, privacy and residential characteristics. Social Isolation and Loneliness in Old Age: Review and Model Refinemnt is an article by G.Clare Wenger and Richard Davis, presents an empirical literature on social isolation and marginalization and links it with an existing publication. He indicates that main factors of social solation includes marital status, social interaction, health conditions, behavior of ‘others', type ot networking and loss ot mobility One ot the tamous sociologists Livson conducted a research ,'The Transition into Retirement and Old Age' in 1962 and found that survival of family, econ omic condition and health condition along with other factors plays important role as individuals adopts to grow old.She is of the view that changes in economic and health status are not only the issues which require our attention. Most important issue is the adjustment of that particular person into the current situation according to the increasing age. Methodology: My research methodology constitutes both primary and secondary research. My primary research was basically a qualitative one, and I choose to visit an old house situated near Bhhatta Chowk. In old house, I interviewed a total of 15 people in two visits to old house. In those 15 people, 12 were the residents of old house, 7 of them were male and 5 were female.Other than these 12 people I interviewed three more ladies who were there to visit their friends. My interviews were structured and semi structured and I asked question according to the situation and personality of the erson. The focus of my questions generally revol ved around their perspective about this residential segregation and the bonds they have developed within themselves in the old house. So extract the proper information I had discussions about their family background and the reasons for which they preferred or forced to live in old house.

Short Essay Writing Samples Secrets That No One Else Knows About

Short Essay Writing Samples Secrets That No One Else Knows About Direct communication from phone to phone doesn't involve a very long procedure since it doesn't need to experience a server like an email. Texting messaging on the opposite hand, lets you convey any information or updates that could be happening at this time. For different companies, a no mobile phone policy on the job could be a big turnoff to prospective employees or could hinder employees' ability to find work done. To keep an eye on work tasks. Short Essay Writing Samples In conclusion, the statement isn't logical since there are a few errors in it. When you check at two sentences, the outcome isn't suitable for the cause. In a location like this, where the temperatures can become very high, it is a necessity so that you're able to cool off. New Step by Step Roadmap for Short Essay Writing Samples Writing a persuasive essay can be hard because you're not just presenting the research materials which you have gathered but you're trying to influence your readers. Reading sample essays will allow you to come up with numerous styles that will allow you to get your message across with clarity and consistency. Writing is quite a strong tool. Essay writing skills is a tough and time-consuming undertaking. Outlines can also function as a brainstorming tool that can provide you a notion of what things to write about. An essay outline is a group of ideas and ideas related to the subject issue. Essays you will show you wish to write. A college essay might need you to go past the elements of writing that you were accustomed to. Inside this section you will locate samples of essays belonging to several essay types and manners of formatting. This section consists of two examples of very good college essays. So the very first step you need to take is to opt for an essay that handles a topic that you understand well. You may choose to refer to some sample essay outlines found in this informative article. You have to remember that the authors of those essays have the ability to compose a high-quality piece since they chose the appropriate topics for them. With essay outline, essays will protect against writer to get off topic or jumping from 1 argument to some other argument that doesn't relate with what it is that you're discussing. Personal essays can on occasion include things like personal information which you would not like to share. Creative essays should have a topic. Therefore, more information would be required to confirm that the 2 studies might be accurately compared. The absolute most important element of this kind of essay is the sort of materials you will use and cite. Factual evidence may also be in the shape of non-numerical info. You cannot use a material if you don't understand it. What Everybody Dislikes About Short Essay Writing Samples and Why It isn't as demanding as other varieties of academic papers, but nevertheless, it can provide you an overall ins ight on writing providing you with the fundamental skills of information gathering, creating an outline, and editing. Don't be worried about a few of them being rather abstract their primary aim is to reveal to you the basic principles that you'll have the ability to transfer to your own writing. A Real Estate company unlike any other centered on the mission of constructing a network of career-minded pros who strive to cultivate their organization and their future. Or plan, or feature a look. Life After Short Essay Writing Samples On the flip side, a well-written essay can increase the possibilities of an ordinary student to become accepted to even the most prestigious schools. This example demonstrates that even for an engineer with years of experience in the specialty, the basics of private essay writing remain the exact same. Likewise, the writer is optimistic concerning the state promise to wash the river. For example, he addresses the way that American history classes do not usually address about the Vietnam War, even though it happened only a short time ago. Ruthless Short Essay Writing Samples Strategies Exploited The cost of an essay is dependent upon the quantity of effort the writer has to exert. Let's say you pay for at least 10 orders for the length of a class. Good rating and excellent reviews should tell you everything that you need to understand about this excellent writing service. The most important point is, you don't need to wait until you find the prompt to come up with an arsenal of kinds of argument-building techniques you may use to back up your points.

Essay on Marriott International - 2309 Words

The Marriot International Hotels have had a long standing history of being recognized as one of the most prestigious hotels. The Marriot Hotel has specific expectations and responsibilities that are expected from their employees on a regular basis. Their reputation derives from the conduct of the Marriott associates who create this professional business environment on a day to day basis. The hotel industry can be a very unpredictable environment. Employees at the Marriott are confronted with situations on a daily that test their values, beliefs and judgments. The reputation of the Marriot is built upon the actions of their employees at these times. It is vital for each member of the Marriott staff to understand the legal and ethical†¦show more content†¦This includes of all company-branded hotels and business and all Marriott business units, Marriot administrative offices, personal and human resources departments, and majority owned subsidiaries. For example, the Ritz- Carlt on is owned by the Marriott Corporation and falls under the same business conduct guide lines as the mainstream Marriott hotels. Its policies and principles like this, is what keeps the Marriott Hotels regarded with such a great reputation as one of the most respected hotels around the world. The Managers of each individual hotel is responsible for the supervision of all employees and associates. It’s their duty as a key leadership figure to enforce and ensure that the expectations of the Marriott Corporation are meet on a daily basis. These supervisors are responsible for overseeing and reporting any discrepancies that make result in a sub level performance of competence that mat occur during, before, and after times of operations. The Marriott Corporation has specific expectations for their employees, the Business Conduct Guide was established to ensure their hotels are kept at a high level of success at all times. Identifying and reporting potential legal issues, is an ar ea where a corporation can neglect to identify a proper set of guidelines for employees to follow. Within the Business Conduct Guide it clearly identifies a listShow MoreRelatedMarriott International1732 Words   |  7 PagesAnalysis of Marriott International: A closer look Marriott International was founded on May 15, 1927 by J. Willard Marriott in Washington D.C. It started out as a root beer stand which grew into a chain of restaurants and hotels (Marriott International Inc., 2013). Now Marriott International has around 3,150 properties for lodging in the United States and 67 in other countries (Marriott International Inc, 2012). The Executive Chairman is Bill Marriott and the President and CEO is Arne Sorenson.Read MoreThe Case Of Marriott International1379 Words   |  6 PagesIn the case of Marriott it started evaluating using a controlled group of customers up to the stage of acquiring an enterprise tool known as One Yield to automate business processes and make better decision [12]. Lastly analytics takes a devoted group of people and infrastructure, according to Davenport the â€Å"most successful analytical competitors take an enterprise approach to analytics† [7] In the last 20 years Marriot has adopted a drudgery incursion into its revenue management, the reason is simpleRead MoreAnalysis Of Marriott International Inc.1208 Words   |  5 Pagesassigned roles and how their proper reinforcement will influence employees to be further engaged in their positions. Marriott International Inc. is a globally leading lodging company which is based in Bethesda, Maryland, USA. Marriott has 146,000 employees from different nations, speaking more than 50 languages and working for Marriott in 66 countries around the globe. (18) Marriott has more than 4,300 properties in 81 countries and territories. The company operates and franchises hotels and licensesRead MoreMcdonald International Marriott International Hotels2960 Words   |  12 Pagescomparisons as they line up next to each other. CATERGORIES Marriott International Hilton WorldWide Brief History - Opened in 1927 J.Willard Marriott opened a rootbeer stand which later evolved into Marriott International Hotels. - Has over 4,000 properties across 72 countries and 18 different brands under the Marriott name. - Courtyard by Marriott was built in 1983 in Atlanta GA and was the first sub Brand to open under the Marriott name. -Hilton Worldwide is one of the largest and fastest growingRead MoreSwot Analysis Of Marriott Group International1902 Words   |  8 PagesSWOT Analysis of The Marriott Group International Overview Marriott Group International is a well-known global brand in the hospitality sector. This hospitality group has more than 3,900 properties, and 18 brands and associates spread across the world. The company, head was founded more than 80 years ago by J. Willard and Alice Marriott while the Marriott family has continued to guide the group. The company has its headquarters in Bethesda, Maryland, USA. In the fiscal year 2013, the group’s reportedRead MoreMarriott International Business Strategy Analysis2780 Words   |  12 PagesFor nearly 88 years, Marriott International has been acknowledged as one of the most impressive hotel in the hospitality industry that offers thousands hotels, resorts, and conference centers. Through the years, the Marriott brands have evolved to provide styles of accommodations, ranging from the casual to the very elegant. Its mission is to provide the best possible lodging services experiences to customers across the United States and around the worl d. Marriott International success is built onRead MoreStrategic Management - Case Study Marriott International3852 Words   |  16 Pages- Case Study Marriott International Introduction The report focuses on Marriott International putting strategic management at the center core of analysis and discussion that allows Marriott strengths and weaknesses to be known and be evaluated according to such SWOT related strategies, CPM, EFE, IE matrix and many other important points for strategic management recognition of Marriott International. There is important account to the strategic analysis of Marriott International, there impliesRead MoreThe Hospitality Industry : Marriott International, And Red Roof Inn1560 Words   |  7 Pagescompanies selected are Marriott International, and Red Roof Inn. The author was given the task to evaluate the strategy that led to the merger or acquisition to determine whether or not this merger or acquisition was a wise choice. Secondly, identify one company that would be a profitable candidate for the corporation to acquire or merge with and explain why this company would be a profitable target. Then, briefly evaluate its international business-level strategy and international corporate-level strategyRead MoreThe Business Operations Of Marriott International Became The Largest Hotel Company1257 Words   |  6 PagesBefore Marriott International became the largest hotel company in the world, it began as root beer stand in Washington D.C. in 1927. Young newlyweds, J. Willard and Alice Marriott, found instant success by offering good food at good prices. Soon, they added hot food items to their menu and restaurant, Hot Shoppes, was born (Marriott, p. 2). From there, they ventured into airline catering, and in 1957, made history by opening t he first hotel in Arlington, Virginia (Marriott, pp. 2-3). By 1982,Read MoreHotel Offices : Marriott International Essay1272 Words   |  6 Pages Introduction Marriott International, Inn is an American enhanced accommodation organization that oversees and establishments a wide arrangement of inns and related hotel offices. Established by J. Willard Marriott, the organization is currently driven by his child, Bill Marriott and Chief Officer Arne Sorenson. Marriott International has more than 4,087 properties in more than 80 nations and regions around the globe, more than 697,000 rooms (starting July 2014), and extra